DiSEqC Accessories

S.115

DiSEqC 1.0 generator of “Write NO” commands. It sends the DiSEqC commands via a coaxial cable connected to its input. It is equipped with 4 independent DC outlets for 0/12 V control, usually from a satellite receiver. Depending on the voltage applied to relevant outlet the following DiSEqC commands are generated:

1. Vertical / Horizontal Polarization

2. Low Band / High Band

3. Position A / B

4. Option A / B

Generated commands are indicated by LED diodes.

S.116

Fixed DiSEqC generator of command “position B”. It adds to any analogue or DiSEqC command from the receiver DiSEqC command “position B”. This device can enable some proprietary receivers to receive satellite channels which are available through multi-switch from second LNB.

S.162-C

DiSEqC 2.0 2in/1out switch. The inputs are controlled by the Write NO “Position” command or by Tone Burst. It allows connection of 2 satellite dishes to one satellite receiver, and is going through for 22kHz and DiSEqC signals.

S.162-CT

Same as S.162-C, but with permanent pass of terrestrial signals from input A to output. Suitable for use in systems where terrestrial signals are distributed via satellite cable.

S.162-CW

Same as S.162-C, but in a weatherproof housing. After installation it is necessary to slide a waterproof sleeves over the connector joints. The sleeves are delivered with the switch.

S.162-D

DiSEqC 2.0 2in/1out switch. The inputs are controlled by the Write NO “option” command. It allows connection of 2 satellite dishes to one satellite receiver, and is going through for 22kHz and DiSEqC signals.

S.162-DT

Same as S.162-D, but with permanent pass of terrestrial signals form input A to output. It is suitable for use in systems where terrestrial signals are distributed via satellite cable.

S.162-DW

Same as S.162-D, but in a weatherproof housing. After installation it is necessary to slide a waterproof sleeves over the connector joints. The sleeves are delivered with the switch.

S.162-E

DiSEqC 2.0 switch with 2 satellite inputs and one terrestrial input, so that both satellite and terrestrial signals are combined at the output. The inputs are controlled by Write NO “ Position” command or by Tone Burst. Satellite inputs are going through for 22kHz and DiSEqC signals.

S.162-F

This switch is an economy version of the switches S.162-C & S.162-g. The S.162-F is supplied in aluminium casting with lugs to attach it. The switch is primarily dedicated to connect two LNBs to one receiver. It is equipped with short-circuit protection.

S.162-G

An outdoor version of S.162-F to connect two satellite antennas to one receiver.

S.162-H

An economy version of other 2in/1out switches. S.162-H is dedicated to connect two universal LNBs to a receiver. The function is slightly different from similar products: S.162-H switches the power from a satellite receiver, but RF paths are simply combined together. Isolation of the two LNBs is done by cutting off power to unwanted LNB. This switch may not work with Twin or Quad LNBs. S.162-H is supplied in an aluminium housing with lugs to attach it. The casting is not weatherproof and the switch is equipped with short-circuit protection.

S.164-A1 & S.164-A2

These switches are successors of well-proven S.164-A. The inputs are controlled from the satellite receiver by Write NO “ Position” and “Option” commands. They are dedicated to connect 4 satellite antennas to one receiver. Short-circuit protection is supplied.

S.164-B1 & S.164-B2

A DiSEqC switch. It has a larger housing with all connectors in-line.

S.164-C

DiSEqC 2.0 switch with an additional terrestrial input, so that the signals of both satellite and terrestrial bands are combined at the output. Satellite inputs of the unit are through for 22kHz and DiSEqC signals.

S.164-D

DiSEqC 2.0 4in/1out switch in a weatherproof housing. The inputs are controlled from the satellite receiver by Write NO “Position” and “Option” commands. The unit allows connection of up to 4 satellite dishes to one satellite receiver, and is through for 22kHz and DiSEqC signals.

S.164-F

A midway between high-end S.164-D and an economy S.164-H. It is dedicated to connect 4 LNBs with one receiver. S.164-f is fixed in aluminium casting with lugs to attach it. Not suitable for humid conditions. Short-circuit protection is a matter of course.

S.164-G

Waterproof version of S.164-F. DiSEqC protocol simplified to 1.0 version.

S.164-H

An economy version of other 4in/1out switches is produced in aluminium casting with lugs to attach it. The product is not weatherproof. Short-circuit protection is a matter of course. The function is slightly different from similar products: S.164-H Switches the supply current, but RF paths are permanent. Separation of the two LNBs is done by cutting off power to an unwanted LNB. This switch may not work with Twin or Quad LNBs.

S.166-A

The unit is fo distribution of satellite and terrestrial signals from 2 Twin Universal LNBs to 2 outputs i.e. to 2 subscribers. In fact, it consists of 2 separate switches S.162-C in one housing. The unit is additionally equipped with a terrestrial input for connection of terrestrial antennas. The inputs are controlled from the satellite receiver by DiSEqC “ Position” command or by Tone Burst. Satellite inputs of the unit are through for 22kHz and DiSEqC signals.

S.168

8in/1out switch designed for direct connection of up to 8 SAT IF inputs to one receiver. Inputs are selected by DiSEqC 1.2 command “ Goto nn” (6B), or by protocol DiSEqC 1.1 inputs 1 to 4 are selectable also by command “Write NO” (38), which makes the unit compatible with standard DiSEqC 4 input switching. Short-circuit protected.

S.105

TV/SAT combiner and splitter. The unit combines satellite and terrestrial signals into one output, or splits the combined signal from one output into 2 outputs, especially into satellite and terrestrial signals. The satellite input/outputs going through for 22kHz and DiSEqC Signals..

S.105-F

TV/SAT combiner and splitter in small compact aluminium not-weatherproof housing. Electrical parameters are the same as for S.105.

~ detail specification ~

S.106

Single (bullet) amplifier of SAT IF Band, suitable for reception system where very long coaxial cable may cause drops in signal strength & quality. Amplifier is powered from receiver via coaxial cable, voltage and 22kHz signal is passed to LNB.

S.107

It is a quadruple TV/SAT combiner and splitter designed for connection to a Quad LNB. The unit is equipped with 4 satellite inputs and terrestrial input, and 4 outputs. This means that both satellite and terrestrial signals can be used from each output. The unit is going through for 22kHz and DiSEqC signals.

S.111

It generates a 0/22 kHz command. This command is sent via a coaxial cable connected to the input of the unit, and allows for control of a connected Universal LNB or 0/22 kHz switch.

S.112-C

2in/1out switch controlled by 0/22 kHz command. It allows for the connection of 2 satellite dishes to one satellite receiver.

S.112-CW

Same as S.112-C, but in a weatherproof housing. After installation it is necessary to slide waterproof sleeves over the connector joints. The sleeves are delivered with the switch.

~ detail specification ~

S.112-E

2in/1out switch controlled by 0/12V applied to DC socket of the switch, usually form a satellite receiver. It is possible to connect 2 satellite dishes to the inputs and a satellite receiver to the output of the unit, or to use a reversible connection, when the signal is distributed from one coaxial cable into 2 satellite receivers (e.g.. Analog and digital ones), and the required receiver is switched by means of 0/12 V on the DC socket. The unit is going through for 22kHz and DiSEqC signals.

DS-41B6

DiSEqC 4 x 1 Switch

950 ~ 2300MHz

DiSEqC Accessories